Understanding & Using Solar DC-AC Inverters – Part 2
- Author Yoni Levy
- Published October 11, 2010
- Word count 897
Understanding & Using Solar DC-AC Inverters – Part 2
Output regulation
We take for granted the fact that our mains power is very well regulated . so
you can plug almost any appliance into a standard point outlet, and it will
operate correctly. That.s because the electricity supplier has enormous generating
plants, with automatic regulation systems to keep the mains voltage and
frequency very close to constant, despite load variations of many megawatts.
Inevitably you can.t get this kind of performance from a much smaller electronic
inverter, connected to a modest battery or solar panel as the energy source.
However most modern inverters can provide reasonably good regulation for loads
of up to their rated capacity (given in watts) . assuming of course that they.re
running from a well-charged battery.
In this type of inverter it isn.t feasible to control the peak-to-peak output,
because this is largely fixed by the battery voltage and the transformer.s step-up
ratio. So in most cases the regulation is achieved in a different way: by varying
the width of the rectangular pulses, to control the .form factor. and hence the
RMS value of the output voltage.
This is called pulse width modulation (PWM), and is usually done by having a
feedback system which senses the inverter.s output voltage (or load current).
When this feedback senses that the load on the inverter.s output has increased,
the inverter.s control circuitry acts to increase the width of the pulses which turn
on the MOSFETs. So the MOSFETs turn on for longer each half-cycle,
automatically correcting the RMS value of the output to compensate for any
droop in peak-to-peak output.
The resulting regulation is usually capable of keeping the RMS value close to
constant, for loads up to the inverter.s full rated output power. However this
approach does have limitations, mainly because it can generally only increase the pulse width to a certain point. (In the extreme, the output becomes a square wave.) This may not be sufficient to allow the inverter to deliver enough RMS output voltage
in short-term overload or .surge. conditions. When many types of appliance are first turned on, for example, they draw a .startup. current which is many times greater than the current drawn when they.re running. This type of surge can overload the inverter, and its protection circuitry may .shut it down. To prevent damage to the transformer and MOSFETs.
Some types of inverter incorporate special .soft start. circuitry, to allow the inverter to cope with this type of short load current surge. The output voltage and power may drop, but at least the inverter keeps operating and allows the appliance to start up.
Even so, there are some appliances and tools that are simply not compatible with inverters, because of their tendency to draw an extremely high startup current.
Examples are refrigerators, freezers, air conditioners or any other appliance where a motor is driving a compressor or pump. As the motor in these appliances often has a very heavy load right at switch-on (with the compressor near .top dead centre.), it can need to draw a huge current simply in order to start rotating.
This type of appliance and tool should really be powered using a suitably rated engine-driven alternator, not a DC-AC inverter.
Voltage spikes
Another complication of the fairly high harmonic content in the output of
.modified sinewave. inverters is that appliances and tools with a fairly inductive
load impedance can develop fairly high voltage spikes due to inductive .back
EMF.. These spikes can be transformed back into the primary of the inverter.s
transformer, where they have the potential to damage the MOSFETs and their
driving circuitry.
The risk of damage is fairly small during the actual power pulses of each cycle,
because at these times one end of the primary is effectively earthed. Transformer
action thus prevents the .other. end from rising higher than about twice the
battery voltage.
However as you can see from Fig.2, there are times during every
cycle of operation when neither of the switching MOSFETs is conducting: the
.flats. between the rectangular pulses. It.s at these times that the spikes can
produce excessive voltage across the MOSFETs, and potentially cause damage.
It.s for this reason that many inverters have a pair of high-power zener diodes
connected across the MOSFETs, as shown in Fig.1.
The zeners conduct heavily as soon as the voltage rises excessively, protecting the MOSFETs from damage.
Another approach is to have high-power standard diodes connected from each
end of the primary to a large electrolytic capacitor, which becomes charged up to
twice the battery voltage. When the ends of the primary attempt to rise higher
than this voltage, the diodes conduct and allow the capacitor to absorb the spike
energy.
Thanks to this type of protection, most inverters are fairly tolerant of moderately
inductive loads. However they may not be able to cope with heavy loads that are
also strongly inductive . like heavy duty tools and machinery, or more than
one or two fluorescent lights.
Quite apart from the generation of voltage spikes, heavily inductive loads tend
to demand current which is strongly shifted in phase relative to the inverter.s
output voltage pulses. This makes it hard for the inverter to cope, because the
only energy available to the load between the pulses is that stored in the
transformer.
RunGreenPower.com will teach you how to build solar & wind power systems for
your home within a weekend.
Check It Now: Homemade Soalr Cells
Article source: https://articlebiz.comRate article
Article comments
There are no posted comments.
Related articles
- The Role of Lighting Stores in Brampton: Shaping Spaces for the Future
- Elevating Your Home with Bold Decor and Vintage Carved Doors
- Transform The Mudroom for The Festive Season
- Rustic Thanksgiving Ambiance with Farmhouse-inspired Doors
- Decorating Spanish Style Villas, Vintage Armoires
- Modern Farmhouse Decor: A Blend of Rustic Charm and Contemporary Style
- Discovering Lighting Stores in Brampton: Spotlight on Fehmilights
- The Role of Smoke Ventilation Systems in Commercial Properties
- Festive Decor with a Global Twist
- Mixer of Styles, The Boho Mid Century Farmhouse
- Elevate Your Remodeling Experience with a One-Stop-Shop Design-Build Firm
- How to Design a Comfortable Family Room
- Your Go-To Lighting Store in Brampton
- Chimney Repair in Toronto: Ensuring Safety and Efficiency
- The Surprising Benefits of Junk Removal and Deep Cleaning
- Illuminating Your Spaces: The Role of Lighting Specialists in Brampton, Mississauga, and Caledon
- Vintage Furniture Trends: Armoires, Rustic Mid-Century, Farmhouse Styles
- Rustic Lodge Décor with Heritage Antique Doors and Furniture with a Soul
- Handcrafted Antique Wood Doors for Cottages: Vintage Charm and Elegance
- Illuminating Your Space: Discovering Lighting Stores in Brampton, Caledon, and Mississauga
- Rustic Carved Doors for Offices: Adding Charm and Character to Your Workspace
- Elevate Your Farmhouse Design with Antique Wood Doors
- Comparing Quick Dry Carpet & Upholstery Cleaning Methods with Conventional Hot Water Extraction
- Removing and Preventing Black Mold on Windows
- Can I Spray Wicker Furniture? A Comprehensive Guide to Painting and Revitalizing Your Wicker Pieces
- Where to Buy the Perfect Office Chair: Your Ultimate Guide to Comfort, Style, and Productivity
- Top Cleaning Tips for Toronto Residents: How to Keep Your Space Spotless
- How to Paint a Vanity Cabinet: A Step-by-Step Guide to Transform Your Bathroom
- What is a Writing Desk? Exploring its Purpose, Design, and Benefits for Your Home
- Vintage Bohemian Charm: Creating a Home Office Retreat