Installing a Bathroom Vanity
- Author Gen Wright
- Published November 25, 2009
- Word count 566
A quick and relatively inexpensive way to freshen the look of your bathroom is to replace the vanity. With a little planning, it can be finished in a day.
First and foremost, measure the space available and note them down. Measure your old vanity too, so that you could use it as a guide when trying to visualise how much bigger or smaller your new vanity will look.
After buying your new vanity, prepare the necessary tools required. Basically, they are adjustable wrenches, pry bar, utility knife, power drill, caulking gun, slip joint pliers, measuring tape, carpenter's level drywall screws, shims, hole saws and stud finder. If unsure or lacking any tools, visit your nearest hardware store and they can advise you. For personal safety, be equipped with safety goggles and face masks. Now, it is time to remove the old vanity.
Firstly, cut water supply by turning off the shut off valves for both cold and hot water supply. With an adjustable wrench, disconnect all supply tubes from the faucet bases. Next, place a pail below the sink trap and use a pair of adjustable pliers to remove the trap.
Secondly, remove the cabinet doors and drawers. Using a screwdriver or socket wrench, remove all the screws that were holding the vanity to the wall. They are usually in the corners or in a rail across the back of the vanity. To remove the top from the base, remove the screws or use a pry bar. Next, remove the basin and gently lift it out. This makes it easier to remove and handle the vanity top. Using a pry bar, remove the backsplash from the wall carefully. Now that the old vanity is out, inspect the area for any damages or rots and repair them before installing the new vanity.
To install the new vanity, locate the studs in the wall and make location marks on the wall. Decide where to position your new vanity and mark its position on the wall. Next, carefully measure the locations of the water pipes and drain lines and mark these pipe locations to the back of the vanity. Use a hole saw at least ½ inch larger than your pipe, and drill holes for the water lines.
Lay old blankets or rags on the floor to minimise floor damage. With someone's help, lift up the vanity into place and drill pilot holes in the back for mounting screws, making sure that the holes are aligned with the wall studs.
If your vanity has a built-in basin, install the faucets first by putting them into the pre-cut holes and then tighten them with a wrench. Attach the water supply lines to the faucets and the tail pipe to the sink drain. Finally, run a bead of adhesive caulk along all top edges of vanity cabinet and place the top on the vanity, making sure it is level and tightly against the wall.
However, if your sink is separate from the vanity top, install the countertop first, then the faucets and then put the sink into the countertop.
Finally, attach all the water supply lines to the supply valves and the sink trap to the drain lines. Run some caulk around the bases of the faucets and the seams where the edges of the backsplash meet the wall. Turn on the water and check for any leaks and you are done!
View bathroom vanity and bathroom tile.
Article source: https://articlebiz.comRate article
Article comments
There are no posted comments.
Related articles
- Vintage Bohemian Charm: Creating a Home Office Retreat
- Embrace the Maximalist Decor : Unleash Your Boldest Dreams
- Fall rustic farmhouse décor with vintage doors and earthy woods
- The Premier Lighting Stores in Brampton, Caledon, and Mississauga: Illuminate Your Space with Style and Precision
- A Brighter, Cleaner Workspace: The Importance of Commercial Cleaning in Auckland
- Antique Doors in a Spanish Modern Home
- Rustic Modern Mountain Cabins Decor
- Why Insulate Your Crawl Space?
- How to Choose the Best Home Renovation Contractor
- All Seasons Cleaning Services: A Top Choice for Tree Removal
- Is Professional Roof Cleaning Worth It? Absolutely.
- Transform Your Property with All Seasons Cleaning Services: A Guide to Our Exterior Painting Process
- A Closer Look at Our 5-Step Exterior Window Cleaning Process - All Seasons Cleaning Services
- The Pros and Cons of Exterior Window Cleaning: Is It Worth the Effort?
- Why Pressure Washing is Essential to Avoid Slippery Sidewalks
- What time of year should you clean your roof?
- How to create Interiors with a Soul
- Antique Doors, Vintage doors with Old Souls
- Bedroom Barn Doors
- Curate Vintage Rustic Charm for your Patio
- How Tri-State Ready Restoration Prepares for the Upcoming Hurricane Season
- 5 Tips for Keeping Your House Warmer in Winter
- Transform Your Kitchen: The Elegance of Premium Cookware and Appliances
- The Benefits Of Installing Solar Panels On Your Home
- Buying a Dream Home in Oakville | Preserve Oakville
- Useful Tips to Harness The Solar Power to Make It Worth in The Virgin Islands
- Embrace Moody Maximalism: Unleashing Rich, Bold Interiors
- Enhance Your Bedroom with Sliding Barn Doors
- A Master’s Hands Launches a New Website to Benefit Customers
- Essex Air Conditioning: Enhancing Comfort and Efficiency Across Essex County