Assessing Engine Issues
- Author Antony Jack
- Published May 3, 2010
- Word count 548
RELYING ON RELATIVE COMPRESSION TESTING TO ASSESS ENGINE ISSUES:
This test uses the digital storage oscilloscope (DSO) and a high amp clamp to measure starter amperage draw at a time base fast enough to see the impact each cylinder has on that draw.
-
Synch the pattern to a given cylinder and use the firing order of the engine to identify weak cylinder(s). A weak cylinder takes less effort to spin through than a strong one does, and that means it also takes less current, and that is displayed on the scope's screen.
-
Modern pressure transducers allow relative compression tests to be done via the exhaust pressure pulses leaving the tail pipe. Cylinders that are healthy will pass equal pressure pulses through the exhaust that the sensor can detect. A weak cylinder will show up as a weaker peak in the pattern.
-
The pattern can be synched to help identify the bad cylinder(s). Here, though, the pulse displayed will be offset from the originating cylinder. When viewing these patterns, look for anomalies rather than specifics. Some exhaust designs cause one bank to have a longer route to follow than the other, and this can reduce the amplitude of the pattern on all the cylinders for that bank.
NOTE: If there is a weakness, the pressure transducer can determine if the fault is in the valve train or cylinder.
-
Be sure to disable the fuel and ignition systems to avoid both over fueling the cylinders and accidental engine start.
-
Remove the oil dipstick and put a rubber hose over the tube, connecting the sensor to the tube.
-
Crank over the engine and watch the pattern. A pressure increase will be present each time a piston heads for bottom dead center.
If the rings are sealing properly, the peaks will be uniform and the loss of compression you found has to be caused by the top end.
SECONDARY IGNITION PATTERNS TO SLOVE ENGINE MYSTERIES:
This takes some skill, but you can master it.
- Look at the average of the firing lines (firing voltage demand) for all the cylinders.
It's normal for the firing line of an individual cylinder to vary as conditions vary in the combustion process. Any cylinder that has a consistently lower firing line is suspect.
- Watch the spark line closely. No compression in a cylinder will not only have a lower firing demand, but the spark (or burn) line will be flat and longer than the others.
NOTE: When a valve doesn't seal, the pressures built up in the cylinder have a path to escape through. It shows up in the pattern as a series of peaks in what should otherwise be a relatively smooth slope. Some turbulence at higher engine speeds is normal, though, so don't confuse the two.
By following the three tests outlined above, you should be able to gain a better understanding of the problems the engine may be experiencing. With luck, you should be one step closer to providing your customer with the auto repair information they need.
Rely on Motor Age for all your automotive news and industry updates. Motor Age has been in publication since 1899, and today reaches over 140,000 automotive service industry professionals, providing them with high-quality auto repair information, body shop news, collision repair news, and much more.
Antony Jack is an expert in the field of Search Auto Parts. He has written various articles on it. To know more Auto Information Online,Auto Parts,Automotive News.
Article source: https://articlebiz.comRate article
Article comments
There are no posted comments.
Related articles
- The Importance of Professional Vehicle Repairs and Maintenance
- Book Pre-Purchase Vehicle Inspections with Kelowna Mechanics
- How to Choose the Right Bore Gauge in Pakistan
- Exploring the Surprising Affordability of Owning a Car in Perth: Does Car Service Really Worth It?
- Why is it important to service your car?
- Navigating Roadside Emergencies with Angel On Wheels in Lawrence, IN
- You Can Do It! Save Money by Replacing Your Headlight
- Veteran motorcyklar
- Truck Repair Near Me: A Comprehensive Guide for American Truckers
- The Simple Car Fixes You Can Do Yourself
- Finding Auto Glass Repair Near Me: Choosing the Right Service Provider
- All You Should Know About Auto Windshields
- Simple DIY Tips to Get Your RV Rubber Roof Repair Done in a Breeze!
- Mechanic Versus DIY: The Vehicle Fixes You Can Do Yourself… And Those Best Left To The Professionals
- Why Are Catalytic Converters Being Stolen?
- 7 Signs Your Car Tire Is About To Burst
- Habits that cost you money to change tires
- DunRite Towing is expanding to an area near you!
- Top-Notch Advantages of Selling Junk Cars and How You Can Do It
- Importance Of Installing Bull Bars In 4×4 Vehicles
- When to call a tow truck
- How to find windshields for your European vintage/classic car
- Understanding If Paintless Dent Repair Could Work for You
- Beginners guide to engine terms
- Useful Tips To Know When Installing And Removing A Car Battery
- Removing Graffiti in USA Made Easier
- The Best Service Of Clear Film Removal At JLN Overspray
- Process of hiring for the remove overspray from plastic service
- 5 Steps To Take When Involved In An Accident
- What Vehicle Repairs Can You Learn to Do?